 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 1 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors fh43b series 2010.9 features 1. low-profile, small pcb mounting area board footprint: reduced approximately 45% weight: reduced approximately 55% (as compared with hirose electric's fh26 series connectors 51 positions) 2. easy solderability on the pc board the soldering leads are on 0.4 mm pitch, exiting on front and back of the connector. 3. conducive traces on the pcb can run under the connector no exposed contacts on the bottom of the connector. 4. easy fpc insertion and reliable electrical connection proven flip lock actuator allows easy insertion of fpc and provides a tactile sensation when fully closed, confirming complete electrical and mechanical connection. 5. easy fpc/ffc insertion fpc/ffc is self-guided in the connector assuring correct and reliable electrical and mechanical connection. 6. accepts standard fpc thickness 0.2mm thick standard flexible printed circuit (fpc) can be used. this is the only ultra-low profile zif connector using standard fpc. 7. board placement with automatic equipment flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. standard reel packaging contains 5000 connectors. 17.8mm(81 pos. shown) 0.9 2.77 no exposed contacts on the bottom of the connector actuator fpc space saving simple fpc insertion can be mounted over conductive traces. lock temporary hold of fpc t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
2 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors specifications ratings current rating 0.2 a operating temperature range -55 to +85c (note 1) storage temperature range -10 to +50c (note 2) voltage rating 30 vrms ac operating humidity range relative humidity 90% max. (no condensation) storage humidity range relative humidity 90% max. (no condensation) recommended fpc thickness 0.2 0.02 mm, gold plated contact pads item specifcation conditions 1. insulation resistance 50 m? min. 100 v dc 2. withstanding voltage no fashover or insulation breakdown 90 vrms ac / one minute 3. contact resistance 100 m? max. * including fpc conductor resistance 1 ma, ac max (ac: 1khz) 4. durability contact resistance: 100 m? max. no damage, cracks, or parts dislocation 10 cycles 5. vibration no electrical discontinuity of 1s or longer contact resistance: 100 m ? max. no damage, cracks, or parts dislocation frequency: 10 to 55 hz, single amplitude of 0.75mm, 10 cycles in each of the 3 axis 6. shock no electrical discontinuity of 1s or longer contact resistance: 100 m? max. no damage, cracks, or parts dislocation acceleration of 981m/s 2 , 6 ms duration, sine halfwave, 3 cycles in each of the 3 axis 7. humidity (steady state) contact resistance: 100 m? max. insulation resistance: 50 m? min. no damage, cracks, or parts dislocation 96 hours at 40c and humidity of 90 to 95% 8. temperature cycle contact resistance: 100 m? max. insulation resistance: 50 m? min. no damage, cracks, or parts dislocation temperature : -55c +15c to +35c +85c +15c to +35c time: 30 2 to 3 30 2 to 3 minutes 5 cycles 9. resistance to soldering heat no deformation of components affecting performance refow: at the recommended temperature profle manual soldering: 350c 10c for 5 seconds note 1. includes temperature rise caused by current fow. note 2. the term "storage" refers to products stored for a long period prior to mounting and use. the operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. note 3. information contained in this catalog represents general requirements for this series. contact us for the drawings and specifcations for a specifc part number shown. materials part material finish remarks insulator lcp color:beige ul94v-0 pa color:black contacts phosphor bronze gold plated --------- metalfttings pure tin refow plated --------- ordering information fh 43b ? 51s ? 0.2 shw ( 10 ) 1 2 3 4 5 6 5 termination type : shwsmt horizontal staggered row mount type 6 plating specifcations (10)gold plating with nickel barrier 1 series name : fh 2 series no.: 43b 3 number of positions : 21to81 4 contact pitch : 0.2mm t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 3 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors connector dimensions unit : mm part number cl no. number of contacts a b c d e fh43b-21s-0.2shw(10) ----- 21 5.8 3.6 4 4.53 5.29 fh43b-25s-0.2shw(10) ----- 25 6.6 4.4 4.8 5.33 6.09 fh43b-31s-0.2shw(10) ----- 31 7.8 5.6 6 6.53 7.29 fh43b-35s-0.2shw(10) 0580-2803-5-10 35 8.6 6.4 6.8 7.33 8.09 fh43b-41s-0.2shw(10) ----- 41 9.8 7.6 8 8.53 9.29 fh43b-45s-0.2shw(10) ----- 45 10.6 8.4 8.8 9.33 10.09 fh43b-51s-0.2shw(10) 0580-2806-3-10 51 11.8 9.6 10 10.53 11.29 fh43b-61s-0.2shw(10) 0580-2805-0-10 61 13.8 11.6 12 12.53 13.29 fh43b-71s-0.2shw(10) 0580-2807-6-10 71 15.8 13.6 14 14.53 15.29 fh43b-81s-0.2shw(10) ----- 81 17.8 15.6 16 16.53 17.29 note1. tape and reel packaging (5,000 pieces/reel). order by number of reels. r ( 2.85 ) ( 0.95 ) ( 0.45 ) ( 2.5 ) ( 0.12 ) d e 0.4 ( 00.08 ) c ( 00.08 ) 0.2 0.4 b a number of contacts a** note 1 the coplanarity of each terminal lead within specified dimension is 0.1 mm max. 2. packaged on tape and reel only. check packaging specification. 3. slight variations in color of the plastic compounds do not affect form, fit or function of the connector. 4. after reflow, the terminal plating may change color, however this does not represent a quality issue. r (1.75) 0.9 0.47 0.2 0.4 2.17 (1.6) (1.2) (0.53) 0.3 (125) 1 0.1 1 0.1 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 4 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors recommended pcb mounting pattern and metal mask dimensions recommended fpc dimensions recommended fpc construction unit : mm part number cl no. number of contacts b c f g h fh43b-21s-0.2shw(10) ----- 21 3.6 4 5.3 4.5 4.94 fh43b-25s-0.2shw(10) ----- 25 4.4 4.8 6.1 5.3 5.74 fh43b-31s-0.2shw(10) ----- 31 5.6 6 7.3 6.5 6.94 fh43b-35s-0.2shw(10) 0580-2803-5-10 35 6.4 6.8 8.1 7.3 7.74 fh43b-41s-0.2shw(10) ----- 41 7.6 8 9.3 8.5 8.94 fh43b-45s-0.2shw(10) ----- 45 8.4 8.8 10.1 9.3 9.74 fh43b-51s-0.2shw(10) 0580-2806-3-10 51 9.6 10 11.3 10.5 10.94 fh43b-61s-0.2shw(10) 0580-2805-0-10 61 11.6 12 13.3 12.5 12.94 fh43b-71s-0.2shw(10) 0580-2807-6-10 71 13.6 14 15.3 14.5 14.94 fh43b-81s-0.2shw(10) ----- 81 15.6 16 17.3 16.5 16.94 recommended meal mask thickness : t=0.1 s 0.04 s 0.04 s 0.04 s 0.80.05 0.020.05 (0.580.03:metal mask) 3.170.05 0.820.03 1.70.05 0.650.03 (0.2) 0.2 (0.30.03:metal mask) 0.40.05 0.4850.05 c 0.4 0.4 (0.180.01:metal mask) b 0.20.02 (0.180.01:metal mask) 0.20.02 (0.550.03:metal mask) (0.680.03:metal mask) (n+1)/2 (n-1)/2 a0.1 (f) g0.05 c0.02 0.40.02 0.20.02 0.250.05 0.250.05 0.2 +0.03 ? 0.02 0.2 +0.03 ? 0.02 0.050.15 0.740.1(even pattern) 0.750.1(odd pattern) 0.840.1(even pattern) 0.850.1(odd pattern) 1.450.1 1.8min 1min 0.670.05(mating area) b0.02 0.670.05(mating area) h0.05(mating area) 0.0550.02 (0.13:odd pattern) (0.1:even pattern) (2.8:stiffeuer) 0.20.02 1.60.05 1.10.05 r0.20.1 max r0.2 r0.20.1 max r0.2 max r0.2 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 5 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors fhb series fpc 1. using single-sided fpc 2. using double-sided fpc 3. precautions 1. this specification is a recommendation for the construction of the fh43b series fpc and ffc (t=0.2 0.02). 2. for details about the construction, please contact the fpc/ffc manufacturers. * to prevent release of the fpc due to its bending, use of the double sided fpc with copper foil on the back side is not recommended. material name material material thickness (m) covering flm layer polyimide 1 mil thick. (25) cover adhesive (25) surface treatment 0.2m thick gold plated over 1 to 6m nickel underplating 4 copper foil cu 1/3oz 12 base adhesive thermosetting adhesive 10 base flm polyimide 1/2mil thick 15 reinforcement material adhesive thermosetting adhesive 30 stiffener polyimide 5 mil thick 125 total 194 material name material material thickness (m) covering flm layer polyimide 1 mil thick. (25) cover adhesive (25) surface treatment 0.2m thick gold plated over 1 to 6m nickel underplating 4 through-hole copper cu 12 copper foil cu 1/3oz 12 base adhesive thermosetting adhesive base flm polyimide 1/2mil thick 13 base adhesive thermosetting adhesive copper foil cu 1/3oz (12) cover adhesive thermosetting adhesive 25 covering flm layer polyimide 1/2 mil thick 13 reinforcement material adhesive thermosetting adhesive 25 stiffener polyimide 4 mil thick 100 total 204 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 6 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors lead portion (400mm min.) top cover tape end portion mounting portion embossed carrier tape no connector inserted (25 pockets min.) no connector inserted (25 pockets min.) no connector inserted (25 pockets min.) (?13 ) (?80) (?380) (l: inside) (m: outside) packaging specification embossed carrier tape dimensions (tape width to 24mm max.) embossed carrier tape dimensions (tape width to 32mm min.) unit : mm part number cl no. number of contacts j k l m n p fh43b-21s-0.2shw(10) ----- 21 16 ----- 7.5 6 17.4 21.4 fh43b-25s-0.2shw(10) ----- 25 16 ----- 7.5 6.8 17.4 21.4 fh43b-31s-0.2shw(10) ----- 31 24 ----- 11.5 8 25.4 29.4 fh43b-35s-0.2shw(10) 0580-2803-5-10 35 24 ----- 11.5 8.8 25.4 29.4 fh43b-41s-0.2shw(10) ----- 41 24 ----- 11.5 10 25.4 29.4 fh43b-45s-0.2shw(10) ----- 45 24 ----- 11.5 10.8 25.4 29.4 fh43b-51s-0.2shw(10) 0580-2806-3-10 51 24 ----- 11.5 12 25.4 29.4 fh43b-61s-0.2shw(10) 0580-2805-0-10 61 24 ----- 11.5 14 25.4 29.4 fh43b-71s-0.2shw(10) 0580-2807-6-10 71 24 ----- 11.5 16 25.4 29.4 fh43b-81s-0.2shw(10) ----- 81 32 28.4 14.2 18 33.4 37.4 1.7 +0.15 0 1.5 +0.1 0 1.750.1 (m) l0.1 k0.1 j0.3 40.1 20.15 80.1 (1.5) (0.3) (0.95) (2.95) (3.85) 1.750.1 l0.1 (m) j0.3 40.1 20.15 80.1 (0.3) (1.5) ?1.5 +0.1 0 ?1.5 +0.1 0 unreeling direction flat surface, for placement with automatic equipment. unreeling direction reel dimensions t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 7 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors temperature profile hrs test condition solder method : reflow, ir/hot air environment : room air solder composition : paste, 96.5%sn/3.0%ag/0.5%cu (senju metal industry, co., ltd.'s part number:m705-221cm5-32-10.5) test board : glass epoxy 100mm72.5mm0.8mm thick land dimensions : 0.2mm0.65mm, 0.2mm0.82mm metal mask : 0.180.55, 0.180.680.1mm thick the temperature profiles shown are based on the above conditions. in individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. consult your solder paste and equipment manufacturer for specific recommendations. max 250c 25c (60sec) (60sec) 0 50 100 150 150c 200c 230c 200 250 preheating time(seconds) start soldering temperature(c) 90~120sec t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 8 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors 3 rotate down the actuator until firmly closed. operation and precautions operation 1. fpc insertion procedure. connector installed on the board. 1 lift up the actuator. use thumb or index finger. 2. fpc removal 1 lift up the actuator pull up the fpc at an angle of approximately 10 and than withdrew it from the connector . 2 insert the fpc (contact surfaces facing down) at angle of approximately 10 to the board surface , making sure that the fpc positioning tabs clear the protrusions on both sides of the connector. lower the fpc down , parallel to the board surface. fpc contact surface faces downward 125 protrusions for the fpc positioning. 15 15 125 protrusions for the fpc positioning. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 9 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors precautions exercise care when handling connectors. follow recommendations given below. 2 axis of rotation 1 do not apply excessive force when opening the actuator prior to fpc insertion. when opening make sure that the force is applied only to the actuator itself, avoiding touching of the contacts. damage to the actuator damage to the actuator actuator 100 0.6 0.5max f connector board 100 0.6 0.5max connector board f assure free rotation of the actuator. fig. 1 [ precautions when mounting connectors on the pcb ] handling before mounting on pcb insertion of the fpc or operation of the actuator prior to mounting on the pcb is not recommended. pc board warpage minimize the warpage as much as possible. the connector is straight within 0.1 mm max. make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. when braking the large pc board into individual boards exercise care not to damage the installed connectors. when attaching the boards or other components with the screws make sure that any stresses will not cause board deflections affecting the mounting areas of the connector. bending of the board for a board width of 100 mm, bending of the board must be 0.5 mm max. (ref to fig. 1) [ precautions during fpc insertion and mating ] pay attention to the following points when inserting fpc. actuator operation t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 10 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors precautions 3 the actuator will rotate 125c do not apply force to rotate further. 4 when opening or closing the actuator, do so at the center section. 5 do not grasp or and lift the actuator (fig. 3) nor insert the nail from the back of it (fig. 4). fig. 3 fig. 4 125 15 protrusions for fpc positioning fpc insertion do not insert the fpc at any high angle from above. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 11 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors precautions as illustrated (fig. 5) angle insertion may cause electrical discontinuity when the fpc is deflected in use. [ routing of the fpc (fpc fully inserted / actuator closed) ] do not apply any pull or upward-directed force to the fpc. do not make any sharp bends of fpc close to the immediate exit from the connector (fig. 7) to avert insertion of the fpc at an angle, consideration should be given to securing enough insertion space when designing the board lay-out. insertion will be difficult when the fpc is too short. contact fpc manufacturer for information about the bending specifications. fig. 5 fig. 7 fig. 6 45 opening of the fpc pattern protrusions fpc positioning fpc positioning tab verification of the fully closed actuator the fpc should be fully inserted, with its positioning tabs fully behind the protrusions on both sides of the connectors insertion slot (fig. 6). t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 12 fh43b series 0.2 mm pitch, 0.9 mm above the board, flexible printed circuit zif connectors precautions [ removing of the fpc ] [ other precautions ] hand soldering precautions when hand soldering: 1 do not perform reflow or hand soldering with the fpc inserted in the connector. 2 do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. 3 do not use excessive amount of solder or flux compounds. operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. the contents of this catalog are current as of date of 09/2010. contents are subject to change without notice for the purpose of improvements. 5-23,osaki 5-chome,shinagawa-ku,tokyo 141-8587,japan phone: 81-3-3491-5300, fax: 81-3-3495-5230 http://www.hirose.com http://www.hirose-connectors.com ? 125 15 protrusions for fpc positioning rotate the actuator to the fully open position (max. angle of 125c) lift the fpc approximately 10 c (making sure that the positioning tabs clear the protrusions on both sides) and carefully withdraw it from the connector. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . |
Price & Availability of FH43B-41S-02SHW
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |